Blog post

The Most Common Types Of Wood Joints

October 10, 2018Olen Murriel

Wooden joinery means binding different pieces of wood to create a beautiful structure, such as furniture, toys or other fixtures. The durability of the product depends on the quality and consistency of the material used in the carpentry process. The product can be made of various materials, and these wood materials vary greatly depending on carpentry requirements. There are several popular types and patterns used in wood processing, such as

Butt Joint

This type of joint is used in some positions considering that it is not the strongest in the connectors used A strong blow with bare hands will break it. The Butt Joint is created at the point of contact between the sides of the board and the creation of glue. Porous grains at the end of the board usually absorb the adhesive faster which is why they are always applied more than desired. For better durability, hold nails or spikes, because the lateral strength of the board installed with glue may be poor Also, make sure to trim the edges of the board to neat boxes.

Rabbet joints

This is a type of wood joint made at the edge of a piece of wood, thanks to which it has two sides open to the end of the surface. In other words, there is an incision or dado (another type of joinery) cut to the edge of the wooden surface. A rabbet joint is also used to create a connection with another piece of wood. It is also used to put a glass plane or wood putty. The most common carpenter with roosts is located on the back of the cabinet, where it can be mounted on the rear panel.

lap joints

The lap joints are of different types and are most commonly used to make tank frames. Dovetail lap, Mitered lap, Cross lap, and End lap and the Half lap are the various laps. A half lap is one widely used in construction works. In this case, the material is removed from each element so that the joining obtained at the end has the same thickness as the thickest piece. The two connected elements will have the same thickness. The damper is reinforced gradually or using a mechanical clamp.

Pocket hole joints

The Pocket hole joints consist used in re-drilling the drill to cut the hole at an angle in a piece of wood to receive the screw into the holes in the pocket. You should use a pocket hole jig placed on the wood in which you want to hide your pocket. Pocket openings are made very quickly and very solidly. It can be placed almost anywhere and, in my opinion, should be used in every store. You can buy a set with everything you need, and Keg is the industry standard for openings in your pocket.

Biscuit joinery

Biscuit joinery is made by cutting the hole into a piece of wood with biscuit joiner and biscuits inserted into the clip slot two pieces of wood together. When the biscuit absorbs up the glue, it swells up and makes an incredibly strong joint You will need a sponge carpenter to make biscuits. Great biscuits were strengthening the joints. Use biscuits to attach frames to cabinets. They work hard, and there are no terminals that can be seen, which indicates a good carpenter.

Tongue and Groove Joints

This method of wood joinery describes the process of joining two pieces of wood along one edge, creating a much wider plat. This combination is much stronger than simply sticking two tablets together because there is more surface there.

Dadoes and Grooves joints

Dadoes and Grooves joints are joints cut in the wood to match the thickness of the wood to be attached in the groove Dadoes run through the grooves running with the grain. These are the same settings, and the results are the same. If you use 3/4-inch plywood and want to make a wardrobe, you will have 3/4-inch dadoes and grooves cut into the plywood to connect them and make the alignment go much easier because there is no place for plywood to go only in Dado or a groove. They are used mainly in working conditions, such as cabinets and entertainment centers. They help in the alignment and strength of joints.

Dovetail Joints

Dovetail Joints are a classic type of wooden joints. They can be produced manually or using a dovetail jig and router There are two parts of dovetail joints and two pins and a tail. they are very consistent connections are the best technique for local carpenters. They are traditionally made hence allows you to do it with a router, and the rows of the blind are often used to draw drawers. They just look to the side. They allow you to climb the stairs countless times without pulling the front of your limbs.

Mortise and tenon joints

One of the oldest and most powerful wooden joints is the Mortise and tenon joints they are placed when you cut a slot in a piece of wood that matches the tenon on another piece of wood. When you are making Mortise and tenon joints, always first place the Mortise and then hold the tenon on the Mortise.

Dado’s joints

Dado’s joints are made by cutting a grooved square hole in a piece of wood, allowing space for another piece to slide in place.

Miter joints

They are made when cutting at an angle of 45 degrees on two pieces of wood and joining together. They are mainly used in furniture finishing and house trimming. It can be made using a Miter saw and can be made on a table saw Angular connections can be strengthened with a sponge joint. There are also compound Miter joints in which the blade tends to create elements. They are used when installing crown molding.

Housing joints

It is the strongest type of wood joint made by joining two pieces of wood cut perpendicularly by cutting a slit or dado in one and fitting the other through it Most bookshelves, cabinets, and drawers are made of these joints. It is cut to the front edge of the material vertically, and the resulting fish reach only one-third of the piece. Finished when another piece of width and similar thickness is inserted into the created slot.

Prev Post Next Post